Dust Masks: FFP2, FFP3 or a Half Mask with Filters?

Cutting concrete, sanding MDF, chasing walls, sweeping a site – dust is part of everyday work in construction and industry. The fine particles you cannot see are the ones that do the damage: they reach deep into the lungs and can cause lasting illness years later. Respirable crystalline silica from concrete, brick and stone is classified in the EU as a carcinogen when generated by work processes.

The good news is that the right mask, worn correctly, gives reliable protection. In this guide we explain the difference between FFP2 and FFP3 disposable masks and a reusable half mask with filters, and how to choose between them for your work.

JSP Force 8 half mask with PressToCheck P3 filters used while cutting

Disposable masks: FFP1, FFP2 and FFP3

Disposable dust masks (filtering facepieces) are tested to EN 149. The standard has three classes, based on how much of the dust the filter stops and how much air may leak in around the edges of the mask:

Class Minimum filter efficiency Maximum total inward leakage Typical use
FFP1 80% 22% non-toxic nuisance dust only – rarely enough on site
FFP2 94% 8% moderate amounts of low-toxicity dust: gypsum, plaster, general sweeping
FFP3 99% 2% fine and hazardous dust: silica from concrete, brick and stone, MDF and hardwood dust, fibreglass

On the mask you will also see NR (non-reusable – for one shift only) or R (reusable), and sometimes D, which means the mask passed an extra clogging test with fine dolomite dust and stays comfortable to breathe through for longer in very dusty conditions.

Valve or no valve?

An exhalation valve makes breathing out easier and reduces heat and moisture inside the mask. For physical work and long periods of wear, a valved mask is much more comfortable. The valve does not reduce the protection for the wearer.

Our disposable masks

Reusable half mask with filters

A half mask is a rubber or silicone face piece (tested to EN 140) with replaceable filters. You keep the mask and change only the filters. Particle filters are tested to EN 143 in classes P1, P2 and P3; P3 is the highest class, with a minimum filter efficiency of 99.95%.

Compared with disposable masks, a half mask:

  • seals better and more consistently – the soft face piece and adjustable four-point harness keep their shape all day;
  • is more economical for daily use – after the initial purchase you only buy filters;
  • can protect against gases and vapours – with combined filters, which no disposable dust mask can do.

The JSP Force 8 half mask with PressToCheck P3 filters is a ready-to-use kit. The Force 8 mask on its own is available in small, medium and large, so each worker can find a size that seals properly. Its Typhoon valve reduces breathing resistance, and the filters attach with a simple twist-and-lock fitting.

What is PressToCheck? Every time you put the mask on, gently squeeze the filter housings and breathe in. If the mask seals, you won't be able to inhale. If you can breathe in or hear air hissing, adjust the mask before you start work. It is a quick daily check that the protection actually works.

Dust plus vapours: combined filters

When dust comes together with solvents, paints, glues or other chemicals, a dust filter alone is not enough. Gas filters are marked with letters and colour codes:

Marking Colour Protects against
P white dust, fibres, fumes and liquid particles
A brown organic gases and vapours with a boiling point above 65°C (solvents, paints, glues)
B grey inorganic gases (excluding carbon monoxide)
E yellow sulphur dioxide and acid gases
K green ammonia and its organic derivatives

For the Force 8 we stock PressToCheck A2P3 filters for organic vapours plus dust, and PressToCheck ABEK1P3 filters for mixed gases plus dust. If the eyes also need protection from irritants and splashes, the JSP Force 10 full face mask takes the same PressToCheck filters.

Which one to choose?

The final choice is made by the employer's risk assessment, based on the type of dust, its concentration and how long people are exposed. As a practical guide:

Task Recommended protection
Occasional sweeping, sanding plaster or gypsum, short dusty jobs FFP2
Cutting, drilling or grinding concrete, brick and stone; sanding MDF and hardwood; fibreglass insulation FFP3 or half mask with P3 filters
Daily dusty work for most of the shift half mask with P3 filters – more comfortable and economical
Dust together with paints, solvents or glues half mask with A2P3 filters
Dust together with ammonia or mixed gases half mask with ABEK1P3 filters

A mask is the last line of defence. Wherever possible, first reduce the dust at source – with water suppression or extraction on cutting tools and by cleaning with a vacuum instead of a broom.

Five rules for masks that really protect

  • Clean-shaven skin. Stubble and beards break the seal of any tight-fitting mask, disposable or reusable.
  • The right size and a fit test. Faces differ. A face fit test confirms that a particular mask seals on a particular person – the safest way to choose a model and size.
  • A seal check every time. Press the filters (PressToCheck) or, with a disposable mask, cover it with both hands and breathe in sharply – the mask should pull slightly towards the face and no air should leak around the edges.
  • Disposable means one shift. NR masks are thrown away at the end of the shift, or earlier if damaged, wet or hard to breathe through.
  • Change filters on time. JSP advises that a P3 PressToCheck filter typically lasts about a week, less in very dusty air; replace it as soon as breathing becomes harder, and in clean air no later than 28 days after opening.

Frequently asked questions

Is FFP3 always better than FFP2?

FFP3 gives a higher level of protection, but it is only as good as the seal. A well-fitting FFP2 can be enough for low-hazard dust, while for silica and other hazardous dust choose FFP3 or a half mask with P3 filters.

Does a valved mask protect less?

No. The valve only opens when you breathe out. The air you breathe in still passes through the filter.

Can I use a dust mask for paint spraying?

No. Dust masks do not stop solvent vapours. For paints, solvents and glues use a half mask with A-type gas filters, such as A2P3.

Order respiratory protection from Start Safety EU

The JSP masks and filters in this article are in stock in our warehouse in Varna. Not sure which protection fits your work, or need masks for a whole team? Call us on +359 (0)87 8810774 or email sales@startsafety.eu – we will help you choose and prepare a quote.

The Start Safety EU team


Author
Sophie Ivanova
What do our customers think?

What do our customers think?

Trusted by thousands who choose us every time they need safety equipment.